Contact UsNeed
help
?










Mart > IP Mart

    
8051 Core By Quotes None 20 MHz None  
The 8051 has gained great popularity since its introduction and is estimated it is  used in a large percentage of all embedded system products.  The  basic  form  of  8051  core  includes  several  on-chip  peripherals,  like  timers  and  counters, additionally there are 128 bytes of on-chip data memory and up to 4K bytes of  on-chip program memory. Introduction
UART Serial Interface Controller By Quotes None 300 MHz None  
UART compatible Serial Interface Controller with receive and transmit FIFOs and support for all standard bit rates from 9600 to 921600 baud.    Applications UART Communications RS232, RS422, RS485 etc. Micro-controller interfacing Introduction
I2C Master Serial Interface Controller By Quotes None 300 MHz None  
Master serial controller compatible with the popular Philips® I2C standard. Features a simple command interface and permits multiple I2C slaves to be controlled directly from  ASIC device. Supports standard (100 kbits/s), fast (400 kbits/s) and custom data rates well above 4 Mbits/s. Setup and hold-times on the SDA pin are fully configurable.    Applications Inter-chip board-level communications Standard 2-wire comms between a wide range of peripherals, MCUs and COTs ICs   Introduction
I2C Slave Serial Interface Controller By Quotes None 300 MHz None  
Slave serial controller compatible with the popular Philips® I2C standard. Permits an I2C Master to communicate with your ASIC device via a set of user-defined config and status registers. Supports standard (100 kbits/s), fast (400 kbits/s) and custom rates in excess of 4 Mbits/s.    Applications I2C slave communication via your ASIC Inter-chip board-level communications Introduction
8-bit / 16-bit Flash memory controller By Quotes None 200 MHz None  
FLASH memory controller ideal for interfacing to a wide range of parallel FLASH memory components . Features a fully synchronous command interface and a set of configurable timing parameters for compatibility with different devices.  Applications Any application where non-volatile storage is required Offline storage of parameters and data via your Chip     Introduction
DDR4 SDRAM Controller Core By Quotes None None None  
Double Data Rate 4 (DDR4) SDRAM Controller Core is designed for use in applications requiring high memory throughput, high clock rates and full programmability.   The core uses bank management modules to monitor the status of each SDRAM bank.  Banks are only opened or closed when necessary, minimizing access delays.  Up to 32 banks can be managed at one time.    The core supports all new DDR4 features, including: 3DS device configurations, write CRC, data bus inversion (DBI), fine granu-larity refresh, additive latency, per-DRAM addressability, and temperature controlled refresh. Introduction
Automotive Electronics Platform By Quotes None None None  
This Platform can decrease timing for develop. Single Chip Solution Integrated Pressure Sensor Integrated Acceleration Sensor Integrated Temperature Sensor 32-bit RISC CPU PWM RF Transmitter (300-450 Mhz) LF Receiver Easy Integrated Customer’s Logic ​ Application Tire Pressure Monitoring System Automotive electronics Introduction
1024X8 Flash By Quotes None None None  
Nor Flash can be used for code storage and data storage with general purpose MCUs and touch panel controller applications.Application in embedded system.   No additional Mask required on Standard CMOS process   Introduction
ASK/OOK Transmitter (R433) By Quotes None None None  
The  IP  is  a  high  performance,  easy  to  use,  ASK  Transmitter  IP  for  remote wireless applications in the 300 to 450MHz frequency band. This transmitter IP is a true “data-in, antenna-out”  monolithic  device.  R433  has  three  strong  attributes:  power  delivery,  operating voltage and operating temperature. In terms of power, the R433 is capable of delivering +10 dBm into a 50Ω load. This power level enables a small form factor transmitter (lossy antenna) such as a key fob transmitter to operate near the maximum limit of transmission regulations. In terms of operating voltage, the R433 operates from 1.8V to 3.6V.   Application Garage Door Openers Remote Controls Home Automation Sensor Networks Security System Fan Controllers   Introduction
Basic IoT Platform By Quotes None None None  
This Platform can decrease timing for develop. Single Chip Solution Integrated Gyroscope Sensor Integrated Acceleration Sensor 32-bit RISC CPU ADC Wi-Fi/Bluetooth SPI/UART/I2C/GPIO Easy Integrated Customer’s Logic Applications Home and Building Automation Smart Energy Internet of Things Introduction
μIP Price Logic Gate Count Clock Rate Technology   Ratings

 1  2  3  4  5  6  7  8  9  10