Needhelp
?
| AES Codec with 8-bit datapath | 20000 Points | 1.300 K Gates | 515 MHz | 180 nm |  |
|
| The IP core implements the NIST FIPS-197 Advanced Encryption Standard and can be programmed to either encrypt or decrypt 128-bit blocks of data using a 128-bit, 192-bit or 256-bit key. The IP has been carefully designed to require minimum logic resources rendering it an ideal solution for low power applications. This has been achieved by using an 8-bit data path size which means that 16 clock cycles are required to load/unload the 128-bit plaintext/ciphertext block. The encryptor receives the 128-bit plaintext block in 8-bit input symbols and generates the corresponding 128-bit ciphertext block in 8-bit output symbols using a supplied 128, 192, or 256-bit AES key. The pre-computed key values are read from an internal round key RAM. A key expander module is provided as an optional module to allow automatic generation and loading of the round key RAM. The decryptor implements the reverse function, generating plaintext from supplied ciphertext, using the same AES key as was used for encryption. The implementation is very low on latency, high speed with a simple interface for easy integration in SoC applications. | Introduction | |||||
| Configurable Reed Solomon Encoder | 30000 Points | 2.500 K Gates | 250 MHz | 180 nm | |
|
| Our IP core implements the Reed Solomon encoding algorithm and is parameterized in terms of bits per symbol, maximum codeword length and maximum number of parity symbols. It also supports varying on the fly shortened codes. Therefore any desirable code-rate can be easily achieved rendering the decoder ideal for fully adaptive FEC applications. ntRSE core supports continuous or burst decoding. The implementation is very low latency, high speed with a simple interface for easy integration in SoC applications. | Introduction | |||||
| One Wire Communication | 1200 Points | 1.500 K Gates | 100 MHz | 130 nm | |
|
| In some particular application, few pin count but still need chip to chip communication. This IP use one wire bi-direction (open drain) to communication. Just like UART , it is consist of one TX and one RX. User can define their own payload freedomly. All devices are connecting through open-drain pull high bus. Every device can send data to others actively. Waveform Application - Analog IC debug - MCU program port - Low pin count IC | Introduction | |||||
| Asynchronous I2C Slave | 999 Points | 578.000 Gates | 100 MHz | 130 nm | |
|
| Unlike Synchronous type I2C slave design need clock to work. This Asynchronous type don’t need base clock . It is very power saving in some application Application : - Power manager IC - Sensor IC - Software wakeup requirement system | Introduction | |||||
| SPI slave in mode 2 | 1000 Points | 254.000 Gates | 192 MHz | 130 nm | |
|
| The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it. The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions: The typical SPI bus architecture is designed as follows: When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line. With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively: | Introduction | |||||
| SPI slave in mode 1 | 1000 Points | 276.000 Gates | 285 MHz | 130 nm | |
|
| The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it. The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions: The typical SPI bus architecture is designed as follows: When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line. With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively: | Introduction | |||||
| SPI slave in mode 0 | 1000 Points | 274.000 Gates | 243 MHz | 130 nm | |
|
| The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it. The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions: The typical SPI bus architecture is designed as follows: When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line. With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively: | Introduction | |||||
| SPI slave in mode 3 | 1000 Points | 256.000 Gates | 285 MHz | 130 nm | |
|
| The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it.The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions:The typical SPI bus architecture is designed as follows:When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line.With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively: | Introduction | |||||
| Clock divider by 3 | 100 Points | 52.000 Gates | 370 MHz | 130 nm | |
|
| There are 2 types of circuits in digital logic world. One is combinational, and the other is sequential. The difference between them is that the latter one has storage (memory) while the former one does not. Thus, in contrast to combinational circuits, whose output depends only on the current values of its inputs, the output of sequential circuits depends not only on the current values of its inputs but also on the past values of them. Based on the characteristic of sequential circuits, we can build counters. In addition, we can further build clock dividers with the counters we designed | Introduction | |||||
| μIP | Price | Logic Gate Count | Clock Rate | Technology | Ratings | |
|---|---|---|---|---|---|---|