Needhelp
?
| PLL 2000M UMC 28 nm logic and Mixed-Mode HPC process | By Quotes | 230.000 μm^2 | 2 GHz | 28 nm |  |
|
| A Phase-Locked Loop (PLL) circuit used to generate the high-speed clock with an operating frequency up to 2000 MHz. This PLL is designed by using the UMC 28 nm logic and Mixed-Mode HPC process. It can be integrated into a chip to generate an accurate clock. | Introduction | |||||
| SPI slave in mode 2 | 1000 Points | 254.000 Gates | 192 MHz | 130 nm | |
|
| The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it. The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions: The typical SPI bus architecture is designed as follows: When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line. With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively: | Introduction | |||||
| SPI slave in mode 3 | 1000 Points | 256.000 Gates | 285 MHz | 130 nm | |
|
| The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it.The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions:The typical SPI bus architecture is designed as follows:When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line.With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively: | Introduction | |||||
| PLL 1600M UMC 28 nm logic and Mixed-Mode HPC process | By Quotes | 270.000 μm^2 | 1.6 GHz | 28 nm | |
|
| A Phase-Locked Loop (PLL) with an operating frequency ranging from 200 MHz to 1600 MHz. This PLL is designed with the UMC 28 nm logic and Mixed-Mode HPC process. It can be integrated into a chip to generate a high-speed clock. The embedded divide-by-4 loop divider allows users to boost the output frequency of up to 1600 MHz. | Introduction | |||||
| SPI slave in mode 0 | 1000 Points | 274.000 Gates | 243 MHz | 130 nm | |
|
| The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it. The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions: The typical SPI bus architecture is designed as follows: When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line. With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively: | Introduction | |||||
| SPI slave in mode 1 | 1000 Points | 276.000 Gates | 285 MHz | 130 nm | |
|
| The Serial Peripheral Interface (SPI) bus, established by Motorola, is a synchronous serial data link. It operates in master/slave and full duplex styles. That is, when a master device initiates a transaction and communicates with a certain slave device, they exchange data bit-by-bit. Furthermore, the single master communication is applied to the SPI bus. Thus, there is always a single master device (with one or more slave devices) on it. The SPI bus contains 4 wires, with each named SCK, MOSI, MISO and SS_n respectively. You may also find alternative naming conventions elsewhere. The following table lists their functions and directions: The typical SPI bus architecture is designed as follows: When the SPI master device wants to communicate with a certain slave device, it asserts the SS_n line of that slave device, and then exchange data using the MOSI and MISO lines based on the toggling SCK line. With clock polarity (CPOL) and clock phase (CPHA) set to different values, the SPI bus can operate in 4 modes. These modes are listed in the following table, where provide means that the communicating master and slave devices provide data on the MOSI and MISO lines respectively on the other hand, capture means that the communicating master and slave devices capture data on the MISO and MOSI lines respectively: | Introduction | |||||
| 12-Bit 50 MSPS ADC in IBM 180 SOI | By Quotes | 280.000 μm^2 | 50 MHz | 180 nm | |
|
| MICIP_ADC12 is compact and low power 12-bit analog-to-digital converter silicon IP. This ADC uses 1.5b/stage pipelined architecture optimized for low power and small area. | Introduction | |||||
| Triple 10-bit 330 MSPS Video DAC IP in TSMC 90 nm | By Quotes | 330.000 μm^2 | 330 MHz | 90 nm | |
|
| MIC_DAC10X3 is a 10-bit Triple DAC designed in TSMC 90 nm logic process. It consists of a current steering DAC. The DAC uses a fully differential architecture. The input data of the DAC is in 1.2 V, in unsigned format. | Introduction | |||||
| Dual-Channel 12-bit 80 MSPS ADC IP in UMC 65 nm | By Quotes | 450.000 μm^2 | 0.8 MHz | 65 nm | |
|
| ADC X is an ultra-compact and very low power analog-to-digital converter (ADC) IP. The 12-bit 80 MSPS Dual ADC includes an internal custom bandgap voltage reference. It is capable of supplying bias currents to other parallel ADCs. IP architecture is robust and can be ported to other 65 nm processes.The ADC uses fully differential pipeline architecture with custom low-disturbance digital correction technique which allows single supply bus for both digital and analog. | Introduction | |||||
| Asynchronous I2C Slave | 999 Points | 578.000 Gates | 100 MHz | 130 nm | |
|
| Unlike Synchronous type I2C slave design need clock to work. This Asynchronous type don’t need base clock . It is very power saving in some application Application : - Power manager IC - Sensor IC - Software wakeup requirement system | Introduction | |||||
| μIP | Price | Logic Gate Count | Clock Rate | Technology | Ratings | |
|---|---|---|---|---|---|---|